If you’ve ever worked with aluminum die castings—whether you’re an engineer designing parts for a car, a consumer goods brand, or someone just learning about metal manufacturing—you probably know that casting alone only gets you halfway there. Die-cast aluminum is lightweight, strong, and versatile, but without the right heat treatment, it won’t live up to its full potential. As a die casting supplier who’s been in this game for over a decade, I’ve seen how skipping heat treatment can turn a perfectly good casting into a part that cracks under pressure, corrodes too fast, or just doesn’t perform like it should. Today, let’s break down the main heat treatment processes we use for aluminum die castings, why they matter, and what makes each one useful for different parts. Aluminum Die Castings

First, let’s start with the basics: why do we heat treat die cast aluminum in the first place? A lot of people don’t realize that as-cast aluminum has a porous, uneven structure. The cooling process during casting creates small gaps, segregated metal grains, and sometimes trapped gases that weaken the part. Heat treatment fixes that—by controlling temperature and cooling rate, we can improve strength, hardness, dimensional stability, and corrosion resistance. It’s like giving a casting a post-cast workout to shape its properties exactly for what you need it for.
The most common heat treatment for aluminum die castings is T6 temper. This is the workhorse, the one we use for 60% of the parts we ship—think engine components, smartphone frames, and structural brackets. What exactly does T6 do? It’s a two-step process: solution heat treatment, followed by quenching, then aging (sometimes called precipitation hardening). Let’s walk through it step by step.
First, solution heat treatment. We load the die castings into a large furnace and heat them to between 510°C and 530°C (that’s around 950°F to 990°F, for the folks who use Fahrenheit). We hold them there for a few hours, long enough to dissolve all the intermetallic compounds that formed during casting—stuff like magnesium-silicon particles, which we add to our aluminum alloy (we use A356 and A380 mostly, by the way—those are the go-to alloys for die casting). The goal here is to get a uniform, solid solution of all the alloying elements throughout the casting, not just in the grain boundaries or porous spots.
Next, quenching. Right after the solution treatment, we take the castings and plunge them into a tank of warm water (around 60°C, not cold tap water) or forced air. This rapid cooling locks the dissolved alloying elements in place, so they don’t have time to form big, weak particles again. If we cooled too slowly, those particles would grow, and the metal would be soft and weak. Quenching gives us a supersaturated solid solution—kind of like a candy that’s overloaded with sugar, ready to crystallize when you’re done.
Then aging. We heat the castings again, this time to a much lower temperature—around 160°C to 180°C (320°F to 355°F)—and hold them there for 8 to 12 hours. During this step, the supersaturated alloying elements start to form tiny, uniform precipitates (the technical term is β” phase, for A356) that are so small they’re invisible to the naked eye. These precipitates block the movement of dislocations in the metal, which is what makes it strong and hard. That’s why T6 parts are way stronger than as-cast ones—we’re creating those tiny reinforcements inside the structure.
But T6 isn’t perfect. One big issue with die cast parts is porosity, especially the kind that’s filled with trapped gas from the casting process. If you have high porosity, quenching can cause the part to deform or even crack, because the trapped gas expands when heated. So for parts with tighter dimensional tolerances, or parts that don’t need maximum strength, we use T5 temper instead. T5 is simpler, faster, and cheaper—no solution heat treatment needed. Here’s how it works: after die casting (while the part is still hot from the mold, usually around 200°C to 300°C), we quench it, then age it in the same low-temp furnace, but for a shorter time—like 4 to 6 hours.
T5 is great for parts where strength isn’t the top priority, but you need speed. Think of things like decorative hardware, lamp housings, or non-structural brackets. It saves us a lot of time in production, and the parts still have decent strength and hardness. The downside is, T5 parts aren’t as strong as T6—their yield strength is usually 10-15% lower, depending on the alloy. But for many applications, that’s more than enough, and the cost savings are a win-win for both us and our customers.
Now, what if you need something that’s not too strong, but super stable dimensionally? That’s where stress relief heat treatment comes in. Every die casting has residual stress from the casting process—when the mold cools, different parts of the casting shrink at different rates, leaving tension inside the metal. If you machine the part right after casting, it might warp later, because those residual stresses relax. Or if it’s used in a hot environment, it could deform. Stress relief fixes that.
We do stress relief by heating the castings to a low temperature—around 150°C to 200°C—and holding them for 2 to 4 hours. It’s way less intense than T6 or T5, so we don’t change the temper of the part much. Instead, we just let those internal stresses dissipate. This is a common step before machining, especially for parts with tight tolerances—like engine blocks or transmission housings, where a warp of even a few microns can ruin the fit. We also do stress relief for parts that are going to be used in high-temperature applications, like components for HVAC systems or industrial equipment.
Wait, there’s another process that’s a little less common but super important for corrosion resistance: annealing. A lot of people confuse annealing with stress relief, but it’s different. Annealing is for when you need a softer, more ductile part—maybe you’re going to form it after casting, or you need it to bend or stretch without breaking. For aluminum die castings, annealing is done at a higher temperature than stress relief, around 340°C to 370°C, and held for several hours, then cooled slowly. This softens the metal by causing the grains to recrystallize, and it relieves residual stress too. But it makes the part way less strong than as-cast, so we only use it for specific cases—like thin-walled parts that need to be formed into a shape after casting, or parts that will be welded, because welding works better on softer, more ductile metal.
I should also mention something that a lot of suppliers skip: hot isostatic pressing (HIP). HIP is a process that’s not standard for every part, but it’s a game-changer for high-stress applications. Here’s how it works: you put the die castings into a sealed chamber, heat them to almost the solution temperature (around 500°C), then apply a super high pressure of inert gas (usually argon, like 100 MPa or more) for a few hours. That pressure squashes all the tiny internal porosity in the casting—those gaps I mentioned earlier—closing them up permanently. The result is a part that’s almost 100% dense, way stronger, and way more corrosion-resistant. We use HIP for aerospace parts, critical automotive components, and medical equipment parts where failure isn’t an option. It’s more expensive, so we don’t do it for every order, but when a customer needs a part that can handle extreme conditions, HIP is non-negotiable.
Now, let’s talk about what to consider when choosing a heat treatment process. As a supplier, I don’t just pick T6 for everything—I work with customers to figure out what their part needs. If they need maximum strength for a structural bracket, T6 is the way to go. If it’s a decorative part that doesn’t need to hold much weight, T5 is faster and cheaper. If they’re machining the part, stress relief is a must to prevent warping. If it’s a high-stress aerospace part, HIP + T6 is the standard. We also have to think about alloy—for example, A380, which is a high-silicon alloy, doesn’t respond as well to T6 as A356, so we adjust the process accordingly.
One mistake we see customers make is thinking “more heat treatment = better part.” That’s not true. If you heat treat a part that doesn’t need it, you’re wasting time and money, and sometimes you can even weaken it. For example, a thin lamp housing that’s only meant to hold a bulb will get no benefit from T6, and T5 will be enough. Over-treating a part can lead to distortion, too, which is a headache for both us and the customer.
Another thing to note: after heat treatment, die castings need a little post-processing, like cleaning and finishing, but that’s a whole other blog. The key takeaway here is that heat treatment is the secret to getting the most out of your aluminum die castings. It turns a raw casting into a part that can stand up to whatever you throw at it—whether that’s a car engine vibrating, a smartphone being dropped, or a medical device sterilized hundreds of times.

At the end of the day, as an aluminum die casting supplier, our job isn’t just to cast a part—it’s to make sure it works as intended. Heat treatment is one of the most impactful steps we take, and it’s what separates a mediocre casting from a high-performance component. If you’re working on a project right now and need to figure out which heat treatment is right for your die cast aluminum parts, or just want to ask a few questions about how heat treatment affects your design, don’t hesitate to reach out. We’re here to help you get the best part for your needs.
Stamped Parts References
- Davis, J.R. (1993). Aluminum and Aluminum Alloys. ASM International.
- Doan, D. (2019). Heat Treatment of Aluminum Die Castings. Die Casting Engineering Magazine.
- American Foundry Society. (2020). Aluminum Die Casting Process and Properties Guidelines.
Yuyao Aozhou Metal Products Co., Ltd.
We are one of the most experienced aluminum die castings manufacturers and suppliers in China. With a professional production team, we are able to meet the needs of the majority of our customers. Please rest assured to buy customized aluminum die castings made in China here from our factory.
Address: No.6, Nanbailonggang, Wuma Industrial Zone, Lubu Town, Yuyao City
E-mail: xqr-2316@163.com
WebSite: https://www.cnaozhou.com/